- Shock-isolated microphone base for GCU250 and GDU150
- Provides superior mechanical noise and vibration isolation - Lightweight ABS material housing - XLR (female) connector - Thick shock-absorbing rubber cushion - Ideal fixture for boardrooms, conference rooms, pulpits, podiums, and newsrooms |
- Bogen speaker signal level control
- Remotely control the volume of up to 150 self-amplified speakers - Rugged and attractive stainless steel plate with engraved lettering - Mounts in a single gang electrical box - Easy and secure terminal strip connections - Passive (requires no DC power) - BGSLC |
This kit is for rack mounting a single TAMB2 unit. The brackets can be mounted at the back end of the unit if a rear-facign orientation is desired.
|
- Bogen single-zone paging universal telephone interface
- Compatible with all standard analog port types -Includes 2 audio outputs with level controls, each of which can provide audio for 150 Bogen self-amplified speakers - Telephone interfaces: loop start trunk, ground start trunk, station access (analog ring-up), page port contact closure activation, page port voice activation - Simple 2-switch interface setup - Programmable activation of AUX contacts - C-form contact - High-impedance transformer isolated background music inputs with volume control - Override paging (using loop start trunk or page port contact closure activation) with zone group - Night ringer (contact closure activation) - Tone triggers (tone and duration selectable, closure activated) with individual zone groups - Tone burst (2 to 7 seconds), chime or slow whoop - Non-volatile memory for setup data (nobackup battery required) - Setup Tone to assistin volume setting - Pluggable terminal strips - Microcontroller-based operation - DTMF programming - DTMF Block to help suppress DTMF tones over paging system - Programmable timers control page duration (station and trunk) - Wall- or Rack-mountable - 2 Year manufacturer's warranty -(+20) Bogen power units BGUTI1 |
- Bogen metal box speakers
- Rugged all-steel surface-mounted enclosure - Full range 8 |
Allows an 8-ohm speaker to connect to 70V or 25V amplifier outputs
T725 Power Taps: 4, 2, 1, 1/2, 1/4, 1/8 watts T72510 Power Taps: 10, 5, 2-1/2, 1-1/4, 5/8 watts Easily-accessed, stripped and tinned wire terminations Small, compact, and cost-effective |
- Indoor and outdoor all-weather speaker with fully-sealed cabinet
- 8-ohm and 70V - Metal-alloy MDTÖ mid/bass speaker cone delivers natural sound with ultra-low distortion - Extremely stable, long-lasting MDT cone structure - High efficiency and power handling for optimum performance - Dual-layer voice coil with separate inner and outer windings for high output with ultra-low distortion - Patented MLSÖ fluid voice coil suspension replaces distortion-causing mechanical spider - Compound rubber surrounds resist UV rays and salt spray - Gold-plated, rust-proof connectors - High-density, injection-molded cabinet resists chipping and scratching - Low-resonance cabinet structure - Easy-to-grasp multi-faceted mounting brackets with 180o swivel - Easy to grip, oversized mounting knobs - Brackets mount with knobs attached for easier and safer installation in hard-to-reach locations - Stainless steel (A8 models) brackets - Corrosion-resistant driver frames & mounting hardware - Attractive styling with ôArmadilloö ridges for stiffness - 2-way speaker systems (A8 models) |
- 8
|
4-watt capacity
8" cone speaker for excellent audio quality 6 different power taps available (4, 2, 1, 1/2, 1/4, 1/8 W) T725 4-watt transformer Off-white enamel over steel grille (ôWö versions) Bright white enamel over steel grille (ôUö versions) Pre-assembled for faster installation Works with both 70V and 25V amplifier outputs Available with volume control û recessed or with knob (VR and VK models only) Screw terminals (BR models only) |
- Suitable for ceiling or wall mounting
- Rugged all-steel surface-mounted enclosure - Full range 8" cone speaker for excellent intelligibility - Compatible with 25V or 70V amplifier systems - Multiple taps at 4, 2, 1, 1/2, 1/4, 1/8 watts - 4-Watt maximum output power - Mounting hardware included (toggle bolts, wood screws and wire crimps) - Knockouts for Wiremold« - VR Models feature recessed volume control at the center of front speaker grille |
- For use with FMH15T horn loudspeaker
- Heavy duty, square, white, cast aluminum with finely perforated mesh insert - For use with BBSM6 or BBFM6 |
- Room selector panel
- Built-in LED annunciators - Space-saving design - Modular versatility - 1 rack space - 25 switches, 3-position, 4-pole lever action with positive detents, self-wiping with precious metal contact surfaces |
-Contructed of cold-rolled steel
Finished in rust-resistant primer For use with any Bogen ceiling grille or assembly |
- Bogen surface mount back box
- WV-Series amps compatible BGBBS |
- Talkback applications module for the Bogen PCM2000 Zone Paging System
- Used with a high-power central amplifier to provide talkback paging in zones with passive speakers - Equipped with controls to adjust talkback volume and talkback delay - Noise reduction switch mutes background noise when no audio activity is present in the zone |
- Interfaces a telephone system with a paging system to allow paging announcements to be made through any telephone
Updated version of the venerable TAMB, functionally the same - Loop start, ground start, & station start (90V ring up) compatibility - Bidirectional for two-way systems - Rack mount or wall mount; half-rack width units can be mounted side by side - background music input with volume control - UL60950 listed; FCC registered - Includes power supply |
- Incorporates a universal interface so that connection to any telephone system is rapid and trouble free.
- Connects to the PCM2000 telephone system via a standard RJ11 plug - Equipped with 3 RJ11 jacks for Override, Page Port/Trunk, and 90V Night Ring/Station |
- Bogen telephone interface input module
- Loop start trunk interface - Ground start trunk interface - Page port interface - Transformer-isolated - Gain/Trim control - Output signal gating - Gating threshold and duration adjustments - Variable threshold limiter - 4 Levels of available priority - Can be muted from higher priority modules - Can mute lower priority modules |
- Bogen terminal and tap selector fitting
BG-TCSPT1 |
- Tile Bridge for Ceiling Speaker
- Load-bearing T-support - Capable of sustaining weight of any Bogen 8 |
- Supports weight of speakers installed in suspended ceilings
- Use with clamping type ceiling speakers |
- 4 types of tones: steady, pulsed alarm, slow whoop, and chime
- Tones triggered by external contact closure (momentary or long duration) - Choice of continuous generation of tones or two-burst operation (except for steady tone) - External audio signal can pass through TG4C and is suppressed during tone generation - Adjustable tone level and pitch - 600-ohm output |
- Transformer-isolated line level input
- Gain/Trim control - Bass & Treble controls - Variable ducking level when muted - Fade back from mute - Screw terminal |
Line impedance-matching transformer
Compact, plug in unit designed for use with power amplifiers (BPA60, HTA models, MT250D) Matches the output of a 600-ohm telephone line to a Bogen power amp input Connections terminated in a keyed nine-pin miniature plug Internal mumetal shielding |
- Monitors audio activity over a wide range of input voltages
- Two sets of C-form (both N.O and N.C) relay contacts respond to audio activity - Four levels of signals: microphone, 600-ohm line, 25V, and 70V speaker systems - Built-in balanced, low noise, high gain microphone pre-am - Transformer-isolated, 600-ohm small signal level output of detected audio available - Works with self-amplified or central-amplified paging systems - Separate microphone pre-amp gain control - Adjustable release delay: 0.25s to 25s - Trigger threshold adjustment - Relay active indicator light - Accessories: PRS40C 12V DC Power Supply (Sold separately) |
- Constructed of 3/8
|
-4-watt capacity
6 power taps available (4, 2, 1, 1/2, 1/4, 1/8 watts) Works with both 70V and 25V amplifer outputs Simulated walnut finish Pre-assembled for faster installation 8 |
- 4-watt capacity
- 6 power taps available (4, 2, 1, 1/2, 1/4, 1/8 watts) - Works with both 70V and 25V amplifier outputs - Simulated walnut finish - Pre-assembled for faster installation - 8 |
- 4W capacity
- 8 |
- 4-watt capacity
- 6 power taps available (4, 2, 1, 1/2, 1/4, 1/8 watts) - Works with both 70V and 25V amplifier outputs - Simulated walnut finish - Pre-assembled for faster installation - 8 |
- 100W, 150W, & 250W models; each with a large power reserve
- 8 module input bays, accepts up to 2 signal-processing output modules or up to 8 input modules - Four priority levels - 4-ohm, 8-ohm, 25V, & 70V outputs - Wall-mountable with Back Box and Door (sold separately) |
- 10-foot long Cable w/ fixed loop
- Cable clamp - Eyebolt - Spacer Nut |
|
|
|
|
Copyright © 2009-2024 A part of the Intelastores, Inc. Store Network Site Designed and Maintained by Inline Internet Systems, Inc. |