Shop by Brand: Sea-Dog

LED Pop Out Combination Bow Light

The LED Pop-Out Combination Bow Light is approved for USCG 2 NM (Colreg 2 mile). A simple twist of the cap allows the light to pop up, ready to use when it’s switched on. Push the cap down, twist to lock, and light disappears into the deck. Constructed of corrosion resistant investment cast stainless steel cap and bezel. Installs with three #10 fasteners (included). IP67 waterproof rating. All USCG approved navigation lights must be mounted properly to provide the correct visual alignment and allow unimpeded sight lines. Please refer to USCG regulations for 1 NM and 2 NM navigation lights for more information.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

LED Rechargeable Handheld Flood Light - 1200 Lumens

This marine grade LED Rechargeable Handheld Flood Light features five 3W high intensity Bridgelux LEDs which produce 1200 lumens. Fully adjustable, the handle allows the light to be hung or propped at many different angles to illuminate the task at hand. Includes both a 12VDC and 120VAC charge adapter. Constructed of a black powder coated aluminum housing with a stamped 304 stainless steel bracket and polycarbonate lens. 7.4V 2200mAh rechargeable Li-battery. Run time 3-4 hours. Charging time 3-4 hours. IP65 rating. CE, RoHS compliant.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

LED Rectangular Flood Light - 1500 Lumens

This marine grade LED Flood Light is constructed with a power coated aluminum housing with a stamped 304 stainless steel bracket. 6 super bright LEDs produce 1500 lumens. Low amp draw. 9-36V. IP67 waterproof rating.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

LED Removable Telescopic All Around Light - 26" - 48" 

LED Removable Telescopic 360° All Around Lights are approved for USCG 2NM (Colreg 2 mile). Constructed of injection molded nylon and aluminum. 12VDC. Low amp draw. Installs with three #8 FH fasteners (not included). 

All USCG approved navigation lights must be mounted properly to provide the correct visual alignment and allow unimpeded sight lines. Please refer to USCG regulations for 1 NM and 2 NM navigation lights for more information.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

LED RGB Rod Holder with Tube Insert

These LED RGB Rod Holders to have translucent tube inserts with bright RGB LEDs and a 30° angle. Or retrofit your existing rod holder with the LED RGB Tube Insert (325189, sold separately). Just remove your existing liner, install the LED RGB Tube Insert, and cut to your mounting face angle. A Bluetooth Smart Phone Controller (403051-1, sold separately) lets you operate this RGB LED Rod Holder from your smartphone (IOS 6 or Android 4.0 and above). Choose from numerous dynamic color-changing modes with adjustable speed and brightness levels or from static color modes. Add multiple LED RGB rod holders with an optional terminal block (426624, sold separately). 

Specifications:

• Constructed of formed 304 stainless steel
• Patented
• Watts: 2.6W
• Voltage: 12V

LED Rod Holder Cap Light - 2" Diameter

LED RGB Rod Holder Cap attaches to the bottom of any 2” diameter rod holder. A Bluetooth Smart Phone Controller (403051-1) lets you operate this RGB LED Rod Holder Cap from your smartphone (IOS 6 or Android 4.0 and above). Choose from numerous dynamic color-changing modes with adjustable speed and brightness levels or from static color modes. Add multiple LED RGB Rod Holder Caps with an optional terminal block (426624). 

Specifications:

• Lumens: 200
• Watts: 2.4W
• Voltage: 12V
• Light Color: RGB
• LEDs: 12
• Patented 

* Sold in Pairs

LED Square Courtesy Light - Blue

LED Square Courtesy Lights are recess mounted in a 1" diameter hole, requiring no installation fasteners. Constructed of investment cast 316 stainless steel. This high quality 1-3/8” square light with two LED bulbs can be mounted to cast light up and down or side to side, depending on the required application. 12V.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

LED Square Courtesy Light - White 

LED Square Courtesy Lights are recess mounted in a 1" diameter hole, requiring no installation fasteners. Constructed of investment cast 316 stainless steel. This high quality 1-3/8” square light with two LED bulbs can be mounted to cast light up and down or side to side, depending on the required application. 12V.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

LED Touch Dimmer Switch for Aurora Pop-Up Table Lamp

This LED Continuous Adjustment Dimmer without On/Off Function is designed to work with lights that are internally switched. Ideal for Aurora Pop-Up Light (404610-3). A center touch sensor activates the color-coded dimming levels. When off, the LED ring is orange; maximum bright, the ring is green; lowest light level, the ring is purple; and in between stages are shades of blue. Memory function turns the light back on at the same brightness level as when it was turned off. Constructed of corrosion resistant 304 stainless steel. 1.5A max. 12/24VDC. IP67 waterproof rating. 

Features:

• 304 Stainless Steel

LED Tube Insert for Existing Rod Holders 11' Long Cut To Fit Any Angle

Retrofit your existing rod holder with the LED RGB Tube Insert. Just remove your existing liner, install the LED RGB Tube Insert, and cut to your mounting face angle. A Bluetooth Smart Phone Controller (403051-1, sold separately) lets you operate this RGB LED Rod Holder Tube Insert from your smartphone (IOS 6 or Android 4.0 and above). Choose from numerous dynamic color-changing modes with adjustable speed and brightness levels or from static color modes. Add multiple LED RGB rod holders with an optional terminal block (426624, sold separately). Patented.

Features:

• 10" x 1-5/8" x 12"
• Weight: 0.25

LED Utility Light White with Black Faceplate 

These LED Utility Lights are constructed of injection molded Delrin for strength, heat resistance, and dimensional stability. Comes standard with low amp draw white LED bulbs. Surface mounts with four #6 FH fasteners (not included).

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

LED Utility Light White with White Faceplate 

These LED Utility Lights are constructed of injection molded Delrin for strength, heat resistance, and dimensional stability. Comes standard with low amp draw white LED bulbs. Surface mounts with four #6 FH fasteners (not included).

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Magneto Safety Kill Switch 

Marine emergency cut-off Kill Switch attaches to your life vest while operating a boat or personal watercraft. Designed to instantly cut battery power when detached. The magneto (red cap) version functions in applications where the circuit is normally open (not complete) with lanyard clip in place on switch. When lanyard is pulled and clip is removed from switch, circuit is closed (complete), allowing grounding to a suitable ground such as a grounding block, the battery, or a suitable area on the engine itself. The kill switch includes a coiled lanyard that is approximately 15" when coiled and 48" when stretched, which should be replaced if worn, cut, or frayed. Mounting hole is 5/8" in diameter. Maximum panel thickness: 5/8". Maximum 5A draw. WARNING: Switch should be tested for proper function before each use.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Manual Oil Change Pump 

Convenient hand pump drains oil through the dipstick on inboard and I/O engines. Includes 2 drain tubes.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Max Blast Single Mini Compact Horn 

Max Blast Single Mini Compact Horn is constructed of injection molded housing under the stamped 304 stainless steel cover, which protects the internal components from corrosion. After a 600 hour salt spray test, this electric horn was completely rust-free! Mounting bracket can be used as a wiring template. When installed, horns should point slightly downward to permit water drainage. At 108 decibels and a frequency (Hz) of 440±20A, this horn meets US Coast Guard's COLREGS and ABYC standard A-23 for use on vessels under 12m (39'). 12VDC. Five-year rust-free warranty. 12VDC. NMMA Type Accepted #2577060.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Max Blast Twin Mini Compact Horn 

MaxBlast Twin Mini Compact Horn is constructed of injection molded housing under the stamped 304 stainless steel cover, which protects the the internal components from corrosion. After a 600 hour salt spray test, this electric horn was completely rust-free! Mounting bracket can be used as a wiring template. When installed, horns should point slightly downward to permit water drainage. At 111 decibels and a frequency (Hz) of 490±20A, this horn meets US Coast Guard's COLREGS and ABYC standard A-23 for use on vessels under 12m (39'). 12VDC. Five-year rust-free warranty. 12VDC. NMMA Type Accepted #2577062.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

MaxBlast Air Horn - Dual Trumpet 

MaxBlast Dual Trumpet Air Horn is constructed of durable chrome plated brass. When installed, the trumpet should point slightly downward to permit water drainage. Display pack includes horn, compressor, air tubing, and mounting hardware. At 121 decibels and a frequency (Hz) of 375±15A/315±15A, this horn meets the US Coast Guard's COLREGS, US Inland Navigation Rules, Annex III Regulations, and ABYC standard A-23 for boats up to 20 meters (66’). 12VDC. Maximum: 20A. NMMA Type Accepted #2577055.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

MaxBlast Air Horn - Mini Dual Trumpet 

MaxBlast Mini Dual Trumpet Air Horn is constructed of durable chrome plated brass. When installed, the trumpet should point slightly downward to permit water drainage. Display pack includes horn, compressor, air tubing, and mounting hardware. At 125 decibels and a frequency (Hz) of 630±15A/525±15A, this horn meets the US Coast Guard's COLREGS, US Inland Navigation Rules, Annex III Regulations, and ABYC standard A-23 for boats up to 20 meters (66’). 12VDC. Maximum: 20A. NMMA Type Accepted #2577058.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

MaxBlast Air Horn Compressor - 12V

The MaxBlast Air Horn Compressor works with all Sea-Dog® MaxBlast air horns. For use in standard installations where head room is not an issue. Does not include air tubing or mounting hardware. Maximum: 20A. 12 or 24VDC. CE compliant.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

MaxBlast Air Horn Compressor - 24V

The MaxBlast Air Horn Compressor works with all Sea-Dog® MaxBlast air horns. For use in standard installations where head room is not an issue. Does not include air tubing or mounting hardware. Maximum: 20A. 12 or 24VDC. CE compliant.

MaxBlast Stainless Steel Trumpet 12V Horn - Dual

MaxBlast Dual Trumpet Air Horn is constructed of durable stainless steel. When installed, the trumpet should point slightly downward to permit water drainage. 

Specifications:

• Stainless Steel
• Dual
• 12V

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

MaxBlast Stainless Steel Trumpet 12V Horn - Single

MaxBlast Single Trumpet Air Horn is constructed of durable stainless steel.  When installed, the trumpet should point slightly downward to permit water drainage.

Specifications:

• Stainless Steel
• Single
• 12V

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Mini Battery Switch Key with Removable Knob - 32V & 100A

These Mini Battery Switches feature a removable knob for extra security. To remove, simply twist the cap to the OUT position and pull. Mini footprint makes it ideal for close quarters. The 422732-1 is rated at 100A continuous and 150A cranking amps. Installation is as easy as drilling a 1-1/8" hole for the 422732-1, inserting the socket body, tightening the locking nut, and connecting the wires. 

Features: 

• 3 Switch positions: On, off, and out
• Constructed of machined brass and injection molded nylon

Specifications:

• Switch Face Width: (inch) 1-1/8"
• Volts: 32
• Amps: 100
• Stud Diameter: (inch) 1/4"

Mini Battery Switch Key with Removable Knob - 32V & 300A

These Mini Battery Switches feature a removable knob for extra security. To remove, simply twist the cap to the OUT position and pull. Mini footprint makes it ideal for close quarters. The 422730-1 is rated at 300A continuous and 1000A cranking amps. Installation is as easy as drilling a 2-1/16" hole for the 422730-1, inserting the socket body, tightening the locking nut, and connecting the wires. 

Features: 

• 3 Switch positions: On, off, and out
• Constructed of machined brass and injection molded nylon

Specifications:

• Switch Face Width: (inch) 2-1/16"
• Volts: 32
• Amps: 300
• Stud Diameter: (inch) 5/16"

Motor Flush Ear Muff 

Outboard motor flushers quickly flush away salt, sand, minerals and contaminates from your lower unit cooling system extending the engine’s service life. Easy to use molded PVC cups deliver fresh water to flush the cooling system through side intakes on the lower unit. Simple garden hose connection, no tools required. Great for winterizing, tune-ups and other maintenance that requires running an outboard engine out of the water.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Motor Well Boot - 3" Split 

Black accordion style seal organizes and protects engine control cables, wires or fuel lines. UV stabilized molded rubber. Boots and rings are cut for trouble free installation without removal of cables. Includes tie wrap.

Motor Well Boot - 4" Split 

Black accordion style seal organizes and protects engine control cables, wires or fuel lines. UV stabilized molded rubber. Boots and rings are cut for trouble free installation without removal of cables. Includes tie wrap.

5 1/2" diameter 

Motor Well Boot - 5-1/2" 

Black accordion style seal organizes and protects engine control cables, wires or fuel lines. UV stabilized molded rubber. Includes mounting ring.

Mounting Plate for 325190 Rod Holder 

Mounting Plate only for the 325190 30° removable rod holder.

Multi-Purpose Cutter - Powder Coated Steel

This Multipurpose Cutter is great for cutting rope, wire, and plastic tubing. Includes two spare utility blades stored in the handle. Replacement Anvils (563311) sold separately. A great addition to any tool box.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Multi-Purpose Cutter Replacement Anvil

This is a replacement anvil only for Sea-Dog's multi-purpose cutter, which is great for cutting rope, wire, and plastic tubing.

Features:

• Constructed of powder-coated steel and ABS plastic
• A great addition to any toolbox