Shop by Brand: Barton Marine

ClamSeal

The ClamSeal™ can instantly repair splits and tears up to 3.5" (90mm) in length without using any hand tools or adhesives.

ClamSeal™ is a glueless repair system that instantly repairs small tears or splits in inflatables above or below the waterline, regardless of the fact that the material may be wet.

The system works by using two half 'shells' that screw together tightly, using the inflatable material itself as a water and air-tight seal.  It is quick and easy to fit and provides an immediate repair that keeps you afloat until a more permanent repair can be made.

The ClamSeal™ can be carried as part of your emergency equipment onboard.  It can be used at sea, on shore, and even underwater as no adhesive or tape is involved.  The clever mechanics of the ClamSeal™ design mean this simple product can keep you safely afloat.

Compatible With:

• RIBs
• Dinghies
• Liferafts
• Buoyancy bags
• Virtually any inflatable product

Features:

• Quick and easy to fit
• Requires no adhesive or tape
• Can be used above or below the waterline
• Provides an instant repair
• Reusable again and again

*Sold as an Individual 

Deck Organizer - Size 2 - 2 Sheave - Black 

Designed for use when diverting mast base control lines and halyards back to the cockpit.  Allowing the crew to sail from the security of the cockpit.

Suitable for boats up to 32' (9.75 M) with halyard size up to 9/16"

Deck organizers can be double stacked.

Technical Specifications:

• Material - Spectro Anodized Aluminum 
• Dimensions (L x W x H) - 5.83" x 1.5" x 1.1" (148 x 38 x 28 mm) 
• Weight -  7.23 oz  (205 g)  
• Sheave Material - Molded Acetal
• Sheave Diameter - 1.73" (44 mm)
• Sheave Width - .71" (18 mm)
• Maximum Line Diameter - .55" (14 mm)

*Sold as an Individual 

Dinghy Mast Prop

Designed to support the aft end of a dinghy mast when towing. Simply fits onto standard transom fittings and is instantly ready for use. Fully adjustable for different transom heights and features a removable pintle to accommodate different transom layouts.

The yolk features a soft neoprene pad to protect the mast, shrouds, and lines. Generous eyelets in the yolk allow for a securing line to be easily attached. A trailer board can be fitted to the cross plate with 2 x 6mm screws (not supplied).

Features:

• Easy to fit
• No fastenings required
• Fully and easily adjustable
• Increases towing safety
• Prevents damage to mast and deck

Double Rope Clutch

Max Rope Diameter:Up 12mm(0.47")
Fastening: 6mm x 4 (0.24" x 4)
SWL:550kg (1,212.54lbs)

The Barton D0550 clutch is designed for cruising and racing yachts. Manufactured from modern lightweight materials to withstand the harsh marine environment. Moulded parts are from high grade plastics which are strong, light and impact-resistant. Cams and bases are from marine grade aluminium, 'Spectro' anodised for high wear resistance and long life.

The true clutch mechanism allows line to be adjusted through the unit in the closed, locked position with minimal slippage. Released under load is positive and requires little effort. The mechanism's opening and closing action is precise and easy to operate, even with cold wet hands. A positive handle lock in the closed position is also featured.

A unique feature of this design is the removable insert on the top face of the handle. Pop this out and you can easily replace with printed coloured inserts to denote at a glance the function of the unit (i.e main, genoa, spinnaker etc).

The clutch's cam and base, manufactured from high grade extruded aluminium, features a specially tempered tooth design which allows for maximum grip with minimal slippage, whilst being kind to your lines. Stainless steel rope fairleads are fitted to both line entry and exit points, this feature prevents wear to both clutch and lines.

The D0550 clutch features the advantage of a bolt together construction which allows for ease of servicing and replacement of parts.

DO 550 Rope Clutch - Base Plate 

Replacement base plate for any size Barton Marine DO 550 Rope Clutch.

*Sold as an Individual

DO 550 Rope Clutch - Cam 

Replacement cam for any size Barton Marine DO 550 Rope Clutch.

*Sold as an Individual

DO 550 Rope Clutch - Handle 

Replacement handle for any size Barton Marine DO 550 Rope Clutch.

*Sold as an Individual

DO 550 Rope Clutch - Spring Assembly   

Replacement spring assembly for any size Barton Marine DO 550 Rope Clutch.

*Sold as an Individual

Drain Plug - Black 15mm (19/32")

This screw-type black drain bung is still among the best available. Supplied with rubber `O' ring for a watertight seal.

Specifications:

• Length: 15mm (19/32")
• weight: 7gm(.23oz)

Extra Large Wincher Pair

The Barton Wincher is a specially designed rubber molding that converts your standard winch into a self-tailing winch.  This tried and tested design has been a firm favorite with Sailors for many years.

The Wincher works by gripping the rope when the drum is fully loaded and under tension, peeling off the line from the underside of the Wincher as you winch to give a true self-tailing motion.

Cleating is achieved by locking the sheet into the Wincher’s ribbed central groove.

Technical Specifications:

• Fits Drum Diameter - 3.5" to 4" (90 to 100 mm)
• Maximum Rope Diameter - .47" to .63" (12 to 16 mm)
• Weight - 13.65 oz (387 g) 

*Sold as a Pair

Furling Drum - 3.74"

Drums are molded from glass fiber reinforced nylon with stainless steel swivel and ball bearing assemblies. Furling drums will accept lines up to 4mm in diameter.

Features:

• Holds up to 8.5M of Line

Specifications:

• Drum Diameter: 95mm
• Sail Area: 100 square foot
• Break Load: 1,108kg
• Safe Working Load: 554kg
• Weight: 281g

Furling Top Swivel

The top head swivel is from machine-turned solid aluminum with stainless steel ball-bearing.

Features:

• Drum Diameter: 25mm
• Sail Area: 100 square foot
• Break Load: 1,108kg
• Safe Working Load: 554kg
• Weight: 55g

Genoa Car - Fits 25mm (1") T Track

Features a precision-turned Ertalyte sheave, through-bolted for extra strength. The positive action plunger mechanism has an easy-grip knob

A popular range of Genoa cars and sliders designed to run on a 25mm (1") 'T' track. All are manufactured from high-quality marine grade aluminum with our unique 'Spectro' grey anodized finish for added protection.

Features:

• 'Spectro' grey anodized finish
• Anodized and supplied in metric lengths
  • The stainless steel plunger stops with positive action
  • Molded nylon slide inserts ensure free running
  • Large, easy-grip plunger knobs
  • Heavy-duty Genoa car options
  • Variety of applications on larger dinghies, dayboats, and light cruisers/racers
  • Cars and sliders are compatible with all makes of 'T' track
  • Modified slider inserts available for obscure sizes
  • 25mm 'T' Section Track
  • Drilled for fastenings and plunger stops

Specifications and Dimensions:

• Length: 80mm (3.15")
• Width: 42mm (1.65")
• Height: 87mm (3.43")
• Sheave Ø: 40mm (1.57")
• Max Rope Ø; 2 x 12mm (2 x 0.47")
• Break Load: 2,280kg (5,026.54lbs)
• SWL: 1,140kg (2,513.3lbs)
• Weight: 247g (0.54lbs)

Genoa Car - Fits 32mm (1-1/4") T Track

Feature precision turned Ertalyte sheaves running on a large diameter center bearing, for friction-free performance under load. Sheaves are designed with extra width to accept two sheets. The sheave axle is through-bolted and riveted for extra strength.

A popular range of Genoa cars and sliders designed to run on a 32mm (1-1/4") 'T' track. All are manufactured from high-quality marine grade aluminum with our unique 'Spectro' grey anodized finish for added protection.

Molded nylon inserts to ensure free, smooth running under load and prevent damage to the finish or potential corrosion.

Features:

• 'Spectro' grey anodized finish
• The stainless steel plunger stops with positive action
• Molded nylon slide inserts ensure free running
• Large, easy-grip plunger knobs
• Cars and sliders are compatible with all makes of 'T' track
• Modified slider inserts available for obscure sizes

32mm 'T' Section Track

Drilled for fastenings and plunger stops. 'Spectro' grey anodized and supplied in metric lengths.

Specifications and Dimensions:

• Length: 109mm (4.3")
• Width: 52mm (2.05")
• Height: 102mm (4.02")
• Sheave Ø: 50mm (1.97)
• Max Rope Ø; 2 x16mm (2 x 0.63")
• Break Load: 3,280kg (7,231.7lbs)
• SWL: 1,640kg (3,615.6lbs)
• Weight: 469g (1.03lbs)

Genoa Slide with Loop for 32mm Track

Have a heavy-duty stainless steel attachment loop, through-bolted and riveted for extra strength. These units will accept most Barton blocks. A popular range of Genoa cars and sliders designed to run on a 32mm (11/4") 'T' track. All are manufactured from high-quality marine grade aluminum and finished with our unique 'Spectro' grey anodized finish for added protection. This slider has molded nylon inserts to ensure free, smooth running under load and prevent damage to the finish or potential corrosion. 

Features:

• 'Spectro' grey anodized finish
• The stainless steel plunger stops with positive action
• Molded nylon slide inserts ensure free running
• Large, easy-grip plunger knobs
• Heavy-duty Genoa car options

32mm 'T' section track

Drilled for fastenings and plunger stops. 'Spectro' grey anodized and supplied in metric lengths

Specifications & Dimensions:

• Length: (mm) 109 / (inch) 4-5/16"
• Width: (mm) 52 / (inch) 2-1/16"
• Height: (mm) 50 / (inch) 1-15/16"
• Break Load: (kg) 2980 / (lbs.) 6,570
• SWL: (kg) 1490 / (lbs.) 3,285 
• Weight (grams): 254 g

Kevlar Cam Cleat Maxi

Manufactured from a composite Kevlar/Zytal material. This advanced material offers performance advantages over carbon fiber and conventional glass-reinforced resins; 'K' cams are solid, lightweight, and have excellent wear resistance. A progressive tooth design ensures maximum holding power on all types of lines, while maintaining minimum wear to both cam and line.

Specifications:

• Max Line Ø: 10mm - 14mm(0.4" - 0.55")
• FasteningsØ: 5mm (0.20")
• Fastenings Center: 50mm (1.97")
• Holding Power: 260kg (573.20lbs)
• Weight: 50kg (110.23lbs)

Large Wincher Pair

The Barton Wincher is a specially designed rubber molding that converts your standard winch into a self-tailing winch.  This tried and tested design has been a firm favorite with Sailors for many years.

The Wincher works by gripping the rope when the drum is fully loaded and under tension, peeling off the line from the underside of the Wincher as you winch to give a true self-tailing motion.

Cleating is achieved by locking the sheet into the Wincher’s ribbed central groove.

Technical Specifications:

• Fits Drum Diameter - 3" to 3.5" (76.2 to 88.9 mm)
• Maximum Rope Diameter - .47" to .55" (12 to 14 mm)
• Weight - 9.8 oz (278 g) 

*Sold as a Pair

Line Tamer - Grey Pair

A line storage device designed to keep cockpits free from unused lines and halyards.  A smooth profile ensures no snagging as crew members brush past. 

Features:

Suitable for rope coils of up to 7.87" (20) cm diameter

*Sold as a Pair

Line Tamer - White Pair

A line storage device designed to keep cockpits free from unused lines and halyards.  A smooth profile ensures no snagging as crew members brush past. 

Features:

• Suitable for rope coils of up to 7.87" (20) cm diameter

*Sold as a Pair

Mast Base Organizer - 4 Block

The Barton Mast Base Organiser is finished in our unique 'Spectro' grey anodizing for a long-lasting finish.

It accepts up to four double tang blocks mounted on individual stainless steel swivel posts but with three deck fixing points.

The unit is fitted close to the mast base to accept halyards, reefing lines, and a topping lift. It is designed to work with our range of deck organizers, rope clutches, and winches, doing away with the need to leave the cockpit when reefing, hoisting, or lowering the mainsail.

Specifications & Dimensions:

• Length: 160mm
• Width: 25mm
• Height: 28mm
• Weight: 166g
• Safe Working Load: 1,540kg
• Break Load: 3,080g
• Fixing Hole: 6mm

Specification comprises:

• 'Spectro' anodized aluminum base
• Four stainless steel swivel posts with nylon base washers
• Four pairs of nylon packing washers for tang blocks
• Used in conjunction with series 1-4 01 090 to 04 090 single blocks

Medium Wincher Pair

The Barton Wincher is a specially designed rubber molding that converts your standard winch into a self-tailing winch.  This tried and tested design has been a firm favorite with Sailors for many years.

The Wincher works by gripping the rope when the drum is fully loaded and under tension, peeling off the line from the underside of the Wincher as you winch to give a true self-tailing motion.

Cleating is achieved by locking the sheet into the Wincher’s ribbed central groove.

Technical Specifications:

• Fits Drum Diameter - 2.75" to 3" (70 to 80 mm)
• Maximum Rope Diameter - .39" to .55" (10 to 14 mm)
• Weight - 7.87 oz (223 g) 

*Sold as a Pair

Quick Cleat - 1/4" - Pair

The Barton Marine Quick Cleat range is perfect for novices and seasoned mariners and takes the place of tying and releasing knots. 

Made of nylon reinforced composite and secures braided lines up to 1/4" (6 mm) with a working load limit of 66 lb (30 kg.)  Sold in pairs, the Barton Marine Quick Cleat offers exceptional value.  

From securing fenders, gear, painter lines, buckets, boat gears or other gear, the Barton Marine Quick Cleat is designed to alter rope tension in one direction, but grips the rope firmly and securely in the other.

Quick Cleats are easy to use.  Simply rotate the lever on top of the cleat, insert the line and release the lever which secures the rope.  Quick Cleats are designed to alter rope tension in one direction but grip the rope firmly and securely in the other.  

Features:

• Dupont Zytel Construction
• Easy to install

Technical Specifications:

• Material - Zytel nylon
• Working Load - 66 lb (30 kg)
• Maximum Rope Diameter - 1/4" (6 mm)
• Height - 1-1/16" (2.7 cm)
• Weight - 2.3 oz (65 g)

*Sold as a Pair

Quick Cleat - 5/16" - Black 

The Barton Marine Quick Cleat range is perfect for novices and seasoned mariners and takes the place of tying and releasing knots. 

Made of nylon reinforced composite and secures braided lines up to 5/16" (10 mm) with a working load limit of 154 lb (70 kg.)  The Barton Marine Quick Cleat offers exceptional value. 

From securing fenders, gear, painter lines, buckets, boat gears or other gear, the Quick Cleat is designed to alter rope tension in one direction, but grips the rope firmly and securely in the other.

Quick Cleats are easy to use.  Simply rotate the lever on top of the cleat, insert the line and release the lever which secures the rope.  

Features:

• Dupont Zytel Construction
• Easy to install

Technical Specifications:

• Color - Black
• Material - Zytel nylon
• Working Load - 154 lb (70 kg)
• Maximum Rope Diameter - 5/16" (10 mm)
• Height - 1-1/16" (2.7 cm)
• Weight - 2 oz (55 g)

*Sold as an Individual 

Quick Cleat - 5/16" - White

The Barton Marine Quick Cleat range is perfect for novices and seasoned mariners and takes the place of tying and releasing knots. 

Made of nylon reinforced composite and secures braided lines up to 5/16" (10 mm) with a working load limit of 154 lb (70 kg.)  The Barton Marine Quick Cleat offers exceptional value. 

From securing fenders, gear, painter lines, buckets, boat gears or other gear, the Quick Cleat is designed to alter rope tension in one direction, but grips the rope firmly and securely in the other.

Quick Cleats are easy to use.  Simply rotate the lever on top of the cleat, insert the line and release the lever which secures the rope.  

Features:

• Dupont Zytel Construction
• Easy to install

Technical Specifications:

• Color - White
• Material - Zytel nylon
• Working Load - 154 lb (70 kg)
• Maximum Rope Diameter - 5/16" (10 mm)
• Height - 1-1/16" (2.7 cm)
• Weight - 2 oz (55 g)

*Sold as an Individual 

Quick Cleat - On a Patch for Inflatables - 1/4"

The Barton Marine Quick Cleat range is perfect for novices and seasoned mariners and takes the place of tying and releasing knots. 

The perfect solution for securing ropes onto inflatables, featuring a Quick Cleat mounted onto a Hypalon ™patch. The unit can be glued into position and has a working load of 30 kg.

Ideal for RIBs, paddleboards and inflatable Kayaks where an easy, quick and simple solution is required for rapid tying of ropes horizontally or vertically.

Quick Cleats are easy to use.  Simply rotate the lever on top of the cleat, insert the line and release the lever which secures the rope.  Quick Cleats are designed to alter rope tension in one direction but grip the rope firmly and securely in the other. 

Securely hold fenders, tender and painter lines, Ribs, buckets, boat gear and equipment, covers, trampolines and water toys of all kinds.

Features:

• Dupont Zytel nylon construction fitted on a Hypalon pad
• Multi-weather adhesive tested up to 113° F (45° C)

Technical Specifications:

• Material - Zytel nylon
• Working Load - 66 lb (30 kg)
• Maximum Rope Diameter - 1/4" (6 mm)
• Height - 1-1/16" (2.7 cm)
• Weight - 2.3 oz (65 g)

*Sold as an Individual 

Quick Cleat - Stainless Steel - 3/8"

The Barton Marine Quick Cleat range is perfect for novices and seasoned mariners and takes the place of tying and releasing knots.  The heavy-duty version is made of 316-grade Stainless Steel and is suited for marina use, larger yachts and ships, workboats, catamarans, and fishing boats to hold marine and boat gear securely on lines up to 5/16" (10 mm.)

The Barton Marine Quick Cleat offers exceptional value and takes the stress out of tying knots.

Quick Cleats are easy to use.  Simply rotate the lever on top of the cleat, insert the line and release the lever which secures the rope.  Quick Cleats are designed to alter rope tension in one direction but grip the rope firmly and securely in the other. 

Securely hold fenders, tender and painter lines, Ribs, buckets, boat gear and equipment, covers, trampolines and water toys of all kinds.

Features:

• Easy to use
• Quality engineered and manufactured

Technical Specifications:

• Material - Marine-grade 316 Stainless Steel
• Working Load -1,188 lb (540 kg)
• Maximum Rope Diameter - 5/16" (10 mm)
• Height - 1" (2.4 cm)
• Weight - 9.9 oz (280 g)

*Sold as an Individual 

Ratchet Block - 55mm

The Barton Ratchet Block is designed to be used on mainsheet systems and spinnaker sheets on dinghies and keelboats and for small yachts up to 30 feet.

Combining high-performance engineering and contemporary design, the 2-3/16" (55 mm) ratchet block is the first in a planned range of sizes, it also offers a stainless steel lever that locks the swivel head if desired.

The new Ratchet Block allows sailors to easily handhold loaded lines and offer a balance between holding power and controlled easing.

Designed for low friction and longevity in harsh marine environments, the Ratchet Block body is manufactured from a composite of high-density nylon and glass fiber reinforced polymer with a high level of UV protection. Internal components are of marine grade 316 stainless steel and the 12 faced aluminum sheave is anodized in gunmetal silver

Technical Specifications:

• Safe Working Load - 661 lb (300 kg) 
• Breaking Load - 2,646 lb (1,200 kg) 
• Maximum Rope Diameter - 3/8" (10 mm)
• Weight - 4.8 oz (135 grams)

*Sold as an Individual

Series 3 Single Snap Shackle & Becket Block - 45mm

Plain Bearing Blocks

Barton plain bearing blocks have a precision moulded acetal sheave running on a large diameter brass bearing, ensuring free running under the highest of loads.

Specifications

• Sheave size: 45mm x 13mm
• Max rope diameter: 10mm
• Safe working load: 400kg / 881lbs
• Breaking load: 800kg / 1763lbs
• Length: 120mm
• Weight: 107g

Series 5 Fiddle Reverse Shackle Block - 54mm

Plain Bearing Blocks

Barton plain bearing blocks have a precision moulded acetal sheave running on a large diameter brass bearing, ensuring free running under the highest of loads.

Specifications

• Sheave size: 54mm x 17mm
• Max rope diameter: 12mm
• Safe working load: 750kg / 1650lbs
• Breaking load: 1500kg / 3300lbs
• Length: 185mm
• Weight: 278g

Series 5 Fiddle Swivel Block- 54mm

Plain Bearing Blocks

Barton plain bearing blocks have a precision moulded acetal sheave running on a large diameter brass bearing, ensuring free running under the highest of loads.

Specifications

• Sheave size: 54mm x 17mm
• Max rope diameter: 12mm
• Safe working load: 750kg / 1650lbs
• Breaking load: 1500kg / 3300lbs
• Length: 185mm
• Weight: 300g

Series 5 Fiddle, Snap Shackle, Becket & Cam Block - 54mm

Plain Bearing Blocks

Barton plain bearing blocks have a precision moulded acetal sheave running on a large diameter brass bearing, ensuring free running under the highest of loads.

Specifications

• Sheave size: 54mm x 17mm
• Max rope diameter: 12mm
• Safe working load: 750kg / 1650lbs
• Breaking load: 1500kg / 3300lbs
• Length: 215mm
• Weight: 568g